Engineered lumber is glued, manufactured wood such as LVL, LSL, PSL, glulam and I-joists, made to carry loads that sawn lumber cannot. The 2021 International Residential Code (IRC) does not give span tables for it; Sections R502.1, R602.1 and R802.1 point each product to its own standard, and sizes come from manufacturer tables.
In plain words, engineered lumber takes wood apart into veneers, strands or boards, then glues it back together with the defects spread out. The result is a member that is straighter, more consistent and available in longer and deeper sizes than a sawn 2x12. It is the usual answer when a span, a header or a ridge goes past what the IRC tables cover.
Key facts
- Structural capacities for structural composite lumber, which includes LVL, PSL and LSL, are established and monitored under ASTM D5456 (2021 IRC Section R502.1.5).
- Prefabricated wood I-joists have their capacities and design provisions set under ASTM D5055 (2021 IRC Section R502.1.2).
- Glued laminated timbers are manufactured and identified under ANSI A190.1, ANSI 117 and ASTM D3737 (2021 IRC Section R502.1.3).
- Cuts, notches and holes in structural composite lumber, glulam, cross-laminated timber, I-joists and trusses are prohibited unless the manufacturer or a registered design professional allows them (2021 IRC Section R502.8.2).
- Trusses, structural composite lumber, glulam and I-joists are braced laterally as the manufacturer recommends rather than by the sawn-lumber blocking rules (2021 IRC Section R502.7, exception 1).
What are the types of engineered lumber?
The main types in house framing are LVL, PSL, LSL, glulam, I-joists, rim board and cross-laminated timber. The first three are grouped by the code as structural composite lumber (SCL).
Engineered lumber types and the 2021 IRC standard for each (Sections R502.1, R602.1, R802.1).
| Product | How it is made | Typical residential use | 2021 IRC section and standard |
|---|---|---|---|
| LVL (laminated veneer lumber) | Thin veneers glued with grain parallel to the length | Beams, headers, ridge beams, I-joist flanges | R502.1.5, ASTM D5456 |
| PSL (parallel strand lumber) | Long veneer strands glued and pressed | Heavy beams, girders, columns | R502.1.5, ASTM D5456 |
| LSL (laminated strand lumber) | Shorter flaked strands glued and pressed | Rim boards, tall studs, headers | R502.1.5, ASTM D5456 |
| Glulam (glued laminated timber) | Layers of dimension lumber glued face to face | Exposed beams, long spans, curved members | R502.1.3, ANSI A190.1, ANSI 117, ASTM D3737 |
| I-joist | Top and bottom flanges joined by a panel web | Floor joists, rafters | R502.1.2, ASTM D5055 |
| Engineered rim board | Panel or SCL product made for the band | Rim and band joists | R502.1.7, ANSI/APA PRR 410 or ASTM D7672 |
| Cross-laminated timber (CLT) | Lumber layers glued at right angles | Floor and roof panels | R502.1.6, ANSI/APA PRG 320 |
The same standards repeat in the wall chapter (Sections R602.1.3 to R602.1.7) and the roof chapter (Sections R802.1.2 to R802.1.8), so a product that qualifies for a floor qualifies on the same basis in a wall or roof. End-jointed (finger-jointed) lumber is not engineered lumber in this sense. Under Section R502.1.1.2 it is graded like sawn lumber and may be used interchangeably with solid-sawn members of the same species and grade.
What is LVL lumber?
LVL is a structural composite lumber made by gluing thin wood veneers together with the grain running the length of the piece. Because the veneers are layered, a knot or split in one sheet is backed up by the sheets around it, so LVL is stiffer and more predictable than a sawn member of the same depth.
LVL is the default engineered beam on many house plans: garage door headers, flush beams in a floor, and ridge beams for vaulted roofs. The header size chart shows where sawn headers in IRC Table R602.7(1) run out, which is why wide garage door headers are usually engineered. A cathedral ceiling often needs a designed LVL or glulam ridge beam for the same reason.
LVL vs. glulam: which should you use?
LVL is usually chosen for concealed beams and headers, and glulam for exposed or very long beams. Both are sized from the manufacturer's tables, and neither is in the IRC span tables.
LVL vs. glulam compared.
| Feature | LVL | Glulam |
|---|---|---|
| Raw material | Wood veneers | Dimension lumber laminations |
| 2021 IRC reference | R502.1.5 (SCL), ASTM D5456 | R502.1.3, ANSI A190.1, ANSI 117, ASTM D3737 |
| Appearance | Industrial; usually hidden | Available in appearance grades for exposed use |
| Width | Often built up from plies fastened as the maker specifies | Made in single wide sections |
| Shape | Straight members | Can be made curved or cambered |
| Cuts and holes | Prohibited unless the maker or a designer allows (R502.8.2) | Same rule |
Multi-ply LVL beams are fastened together with the manufacturer's nailing or bolting pattern, not the sawn-lumber nailing in Table R602.3(1). The built-up beam article covers the sawn-lumber version.
LVL vs. LSL vs. PSL
All three are structural composite lumber under ASTM D5456; they differ in the size of the wood pieces inside. LVL uses whole veneer sheets, PSL uses long strands cut from veneer, and LSL uses shorter flakes. PSL is common where a heavy girder or post is needed. LSL is often used for rim boards and for tall wall studs where straightness matters. Capacities differ by product and brand, so read the manufacturer's literature for the exact member, never a generic chart.
What is an I-joist?
An I-joist is a manufactured joist with top and bottom flanges and a thin panel web, shaped like the letter I. The 2021 IRC sets its capacities under ASTM D5055 (Section R502.1.2). I-joists are light, long and consistent in depth, which keeps floors flat. Spans, spacing, bearing, blocking and web holes all come from the manufacturer, and the IRC floor joist tables in the floor joist span table do not apply.
What rules apply to engineered lumber on site?
The IRC hands most engineered lumber decisions to the manufacturer, with a few fixed rules.
- No field cuts or holes without approval. Sections R502.8.2 (floors) and R802.7.2 (roofs) prohibit cuts, notches and bored holes in SCL, glulam, CLT, I-joists and trusses unless the manufacturer permits them or a registered design professional designs for them. The sawn-lumber limits in notching floor joists do not carry over.
- Bracing per the manufacturer. The full-depth blocking rule of Section R502.7, and the bridging rule of Section R502.7.1 for joists deeper than 2x12, both exempt trusses, SCL, glulam and I-joists, which are laterally supported as the manufacturer recommends. See joist blocking and bridging.
- Bearing still applies. Section R502.6 requires the ends of each joist, beam or girder to have at least 1-1/2 inches of bearing on wood or metal and at least 3 inches on masonry or concrete, unless on approved hangers. Manufacturers often require more.
- Rim board for deck ledgers. Section R507.9.1.2 allows a deck ledger on a band joist of 2-inch nominal solid-sawn spruce-pine-fir or better, or on engineered rim board of at least 1-inch nominal that meets Section R502.1.7.
- Rim board headers. Section R602.7.2 allows rim board headers sized from Table R602.7(1) and built per Figure R602.7.2, with full-height studs at each end.
How engineered lumber appears on a framing plan
Engineered members are labeled by product, not by sawn size: for example a beam tag naming LVL, the ply count and the depth, with the note "size per manufacturer" or a reference to the engineer's calculation. I-joist floors list the series and spacing. Show bearing points and posts so the load path is clear.
These notes describe 2021 IRC provisions only. The adopted code edition and local amendments govern, and every engineered product uses its manufacturer's tables and installation guide. The American Wood Council publishes design values and span tables for sawn lumber; engineered products have their own.
Summary
Engineered lumber covers LVL, PSL and LSL (structural composite lumber under ASTM D5456), glulam, I-joists, rim board and CLT, each tied to a standard in 2021 IRC Sections R502.1, R602.1 and R802.1. None of it uses the IRC span tables. Do not cut or drill it without the manufacturer's or a designer's approval (R502.8.2), and brace it as the manufacturer says.
Framing Plan draws joist layouts, beams and openings and exports PNG, PDF and DXF. It does not size members or check engineered products, and its editor works in millimeters. Open the framing studio to place the beams and joist field for a preliminary drawing, then size each engineered member from the manufacturer's tables.