Free calculator

Floor Joist Span Calculator

Pick a joist size, species, grade, spacing and load to read the maximum allowable floor joist span from the 2021 IRC span tables.

Read it from the grade stamp.

Floor weight: joists, subfloor, finishes and any ceiling below. Heavy finishes need 20 psf.

Clear span between supports, in feet. Leave blank to skip the check.

Maximum clear span
15-7 (ft-in)
Joist
2x10 Douglas fir-larch #2
Spacing
16 in. on center
Loads
40 psf live, 10 psf dead, L/360
Source
2021 IRC Table R502.3.1(2)

How do you read the floor joist span result?

The result is the longest clear span the 2021 IRC allows for that joist size, species, grade, spacing and load. Spans are written in feet and inches, so 15-7 means 15 feet 7 inches. The values come from Tables R502.3.1(1) and R502.3.1(2), and the calculator shows which table it used.

If your clear span is longer than the result, step up one setting: a deeper joist, closer spacing, a better grade or a stronger species. Our floor joist span table prints the same cells in full, and floor joist spacing explained covers what each spacing means on site.

Floor joist span quick reference

Table: maximum clear span for a No. 2 joist at 16 inches on center, 40 psf live load and 10 psf dead load (2021 IRC Table R502.3.1(2)). This is the answer to how far a 2x8, 2x10 or 2x12 can span in most living areas.

Species2x62x82x102x12
Douglas fir-larch9-912-915-718-1
Hem-fir9-112-015-217-7
Southern pine9-411-1014-016-6
Spruce-pine-fir9-412-315-517-10

What clear span means

Clear span is the horizontal distance between the faces of the supports, measured inside face to inside face. The joist is longer than the clear span because it needs bearing at each end. Section R502.6 requires at least 1-1/2 inches of bearing on wood or metal and at least 3 inches on masonry or concrete, unless joist hangers carry the ends.

What L/360 deflection means

Both floor tables limit deflection to span divided by 360 under live load. A 12 ft joist (144 inches) may then sag no more than 0.4 inch under live load. Meeting the limit keeps floors from feeling bouncy and protects tile and plaster, so it often governs before strength does.

Limits of the tables

  • The tables assume sawn lumber of the listed species and grades. I-joists, LVL and trusses use the manufacturer's tables.
  • Notches and holes reduce capacity. For sawn joists, Section R502.8.1 limits a notch to one-sixth of the joist depth, keeps it out of the middle third of the span, and limits a bored hole to one-third of the depth.
  • Point loads, bearing walls, tubs, stone floors and cantilevers need their own check. See how a floor framing plan shows them.
  • Table R502.3.1 applies where the live load is no more than 30 or 40 psf and the dead load is no more than 20 psf.

Related spans: ceiling joist span chart and deck joist span and spacing.

Lay out the whole floor

Framing Plan is a free browser tool for preliminary floor and low-slope roof framing layouts. Draw joists, beams and openings and export PNG, PDF or DXF.

Open the framing studio

Frequently asked questions

How far can a 2x10 floor joist span?

Under 2021 IRC Table R502.3.1(2), with a 40 psf live load and 10 psf dead load, a #2 2x10 at 16 inches on center spans 15 ft 7 in in Douglas fir-larch, 15 ft 5 in in spruce-pine-fir, 15 ft 2 in in hem-fir and 14 ft 0 in in Southern pine. These are clear spans between supports.

How far can a 2x8 floor joist span?

At 16 inches on center with a 40 psf live load and 10 psf dead load, a #2 2x8 spans 12 ft 9 in in Douglas fir-larch, 12 ft 3 in in spruce-pine-fir, 12 ft 0 in in hem-fir and 11 ft 10 in in Southern pine, per 2021 IRC Table R502.3.1(2). Wider spacing or a 20 psf dead load shortens each span.

Which table applies to bedrooms?

Section R502.3.1 allows Table R502.3.1(1), with a 30 psf live load, for joists that support sleeping areas and attics reached by a fixed stairway, as long as the dead load does not exceed 20 psf. Every other floor area uses Table R502.3.1(2) at 40 psf. If a room might change use, size it from the 40 psf table.

What does clear span mean?

Clear span is the horizontal distance between the faces of the supports, such as the inside faces of two walls or a wall and a beam. It is not the overall length of the joist, which is longer because it must bear on each support. Measure inside face to inside face, then compare that number with the table result.

Do these spans apply to I-joists or LVL?

No. The IRC tables cover sawn lumber of the listed species and grades at the listed loads only. For other grades, species or loading, Section R502.3 sends you to the AWC Span Tables for Joists and Rafters. I-joists, LVL and floor trusses use the manufacturer's span tables and installation details.

Results are preliminary layout figures for planning. The building code edition and local amendments adopted where you build govern, and the building official has the final say.